 |
 |
 |
|
BendPak HD-9EWT 9,000-lb. Capacity / Four-Post Lift / Extra-Wide / High Lift
SKU: 5175607
BendPak’s HD-9EWT is the perfect solution for all your storage needs. This extra-tall and extra-wide lift offers ample overhead clearance and enough side room to easily park light-duty trucks, SUVs, and virtually any low ground-clearance vehicles. With over 6 inches of additional width compared to the HD-9XW, this lift is perfect for wide cars and off-road vehicles.
Built for garages with plenty of space, the BendPak HD-9EWT is perfect for high ceilings and high-rise vehicles. Unlike the narrower HD-9ST four-post lift, the HD-9EWT comfortably accommodates wide-body trucks and SUVs, avoiding concerns about mirror and door scratches. With a substantial 82” rise from the runways, it lifts heavy vehicles higher, providing plenty of room for taller techs to work beneath. Plus, it offers ample space for high-clearance trucks and SUVs, ensuring compatibility with taller vehicles.
Dual-hub cable sheaves are more expensive to manufacture, but they prevent axles, sheaves, and cables from burning out prematurely. The HD-9EWT’s multi-level locking positions ensure that technicians can lock the lift at varied heights, eliminating the need to crouch or reach uncomfortably while performing maintenance. The electric-hydraulic power system allows you to stop, start, and reverse your four-post lift on a dime, with controls within easy reach.
Each four-post lift comes with four lifting cables made from superior-grade stainless steel, rated to handle 14,400 lbs. each. These cables are hidden within the post columns for safety and a streamlined look. The integrated design routes all lifting cables, airlines, safety latches, and sheaves internally, adding to the lift’s sleek appearance.
Safety is a top priority with each and every BendPak lift. Four locks engage simultaneously as the lift is raised, and a backup locking system catches cable slack in the unlikely event of cable failure. Longer approach ramps and low runways make lifting sports cars and other low-standing vehicles easier than ever.
The HD-9EWT is a solid choice for both DIY enthusiasts as well as professional shop owners. The added ceiling clearance is particularly valued in shops, providing ample space for lower-ceiling vehicles. For anyone looking to solve their vehicle storage problems while maximizing their space, the HD-9EWT is the perfect solution.
| BendPak HD-9EWT Four Post Lift |
| Lifting Capacity |
9,000 lbs. / 4,082 kg |
| Max Capacity at Front Axle |
4,500 lbs. / 2,041 kg |
| Max Capacity at Rear Axle |
4,500 lbs. / 2,041 kg |
| A. Min. Runway Height |
4.75 in. / 121 mm |
| B. Maximum Rise |
82.165 in. / 2,087 mm |
| C. Maximum Lifting Height |
87 in. / 2,208 mm |
| D. Overall Width ± .125 in. / 3 mm |
117 in. / 2,970 mm |
| E. Outside Length |
198 in. / 5,028 mm |
| F. Overall Length |
224.50 in. / 5,703 mm |
| G. Height of Post |
100 in. / 2,537 mm |
| H. Distance Between Posts |
107 in. / 2,716mm |
| I. Drive-thru Clearance |
93.25 in. / 2,371 mm |
| J. Runway Width |
19 in. / 482 mm |
| K. Runway Length |
182.25 in. / 4,629 mm |
| L. Width Between Runways |
35.75 in. – 42.0 in. / 910 MIN – 1,068 mm MAX |
| M. Runway Centerline |
57.75 in. – 64.00 in. / 1,468 – 1,626 mm |
| N. Outside Edge of Runways |
76.75 in.- 83 in. |
|
/ 1,950 – 2,108 mm |
| Max. Load Operating Pressure |
135 in. / 3,429 mm |
| Min. Wheelbase @ Rated Capacity |
115 in. / 2,921 mm |
| Min. Wheelbase @ 75 Capacity |
95 in. / 2,413 mm |
| Min. Wheelbase @ 25 Capacity |
80 in. / 2,032 mm |
| Locking Positions |
17 spaced every 4 in. / 102 mm |
| Motor |
220 VAC, 60 Hz, 1 Ph (special voltages available upon request) |
DISCLAIMER
BendPak makes no promises, guarantees or assurances that our products meet any state, county, federal or international mandated permit, license, code, standard, certification, or any other mandate other than what is listed or shown on BendPak website(s), or any BendPak online or published catalog. Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201. Consult www.autolift.org for a complete list of lift models that meet ANSI/ALI ALCTV-(current edition) or ANSI/UL 201, or contact BendPak via [email protected]. Buyer assumes full responsibility for any state, county, federal or international mandated permit, license, code, standard, certification, or any other mandate required related to the installation and/or operation of any BendPak or Ranger product. BENDPAK will not be responsible for any charges, fines, liens, or other levies imposed on the Buyer related to any special or regional structural, seismic or any other building code and/or codes such as the Uniform Building Code (UBC), International Building Code (IBC), or any other state, county, federal or international mandated permit, license, code, standard, certification, or other mandate, law, rule, regulation or directive by any other agency, government, administrations, or corporations whether state, county, federal, or international mandated.
|
| WARNING: California Prop 65 |
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
HD-9EWT
- 9,000-lb. maximum lifting capacity
- Freestanding design
- High-rise
- Better suited for wide cars and off-road vehicles
- Perfect for parking, storage, and service
- Runways accommodate narrow and standard vehicles
- Runways include rail-kit for optional accessories
- Electric-hydraulic power system
- Single hydraulic cylinder mounted underneath runway
- Fully enclosed lifting cables, safety locks, and sheaves
- Internal anti-sway slider blocks in each column
- Oversized self-lubricating cable rollers
- Multi-position safety locks in each column
- Adjustable safety locks in each column
- Adjustable lock ladders
- Runways feature a durable matte finish
- Push-button pneumatic safety release
- Independent backup slack-cable safety latches
- Customizable power unit location
- Removable approach ramps for additional drive-under clearance
- Longer approach ramps for low-ground clearance vehicles available
|
|
|
|
|
|
|
