Authorized Dealer

BendPak has been building benders for more than three decades, with a single overriding priority - performance. Our assembly guys and R & D teams are constantly testing each model as it comes off the assembly line to make sure that no corners are cut. Each phase of production is scrutinized by team leaders whose only responsibility is to make sure that everything works and works right. No, we’re not the only bender manufacturer out there. There are others, but not as dedicated and well respected.

• Quick-Change Bending Dies - Who has time to waste? Especially when you have a car in the air and others lined up. When we first came up with the idea of twist-lock tooling and quick-change bending dies others said it wouldn’t work. Well it did, and it still does. In fact it still does so well that others copied. Imitation really is the best form of flattery.


• 180-Degree Bending Capacity - You say you have to bend deep. Well, how does a U-shape sound? Be sure to ask for our 180-Degree dies if you’re planning to bend more than 170 degrees. You’ll get perfect deep bends on a 5” radius without the pipe sticking or hanging up. That’s because we use an exclusive relief cut design on our bending dies that helps maintain the pipes uniformity throughout the bend cycle and eliminates excessive “crimping” or deformation.


• 3” Bending Capacity - We’ve purposely built 3” bending capacity into every BendPak bender so that you can order three inch dies when you need them. Our three inch bending dies are a fine example of our commitment to quality. Sure there heavy, but take a close look at their design. We took ordinary bending dies and made them not so ordinary. No other manufacturer uses this exclusive step-cut process for the die rails that actually helps contain the larger size tubing better and gives you a more uniform bend. Not only can you bend three inch tubing but we’ve made it possible for you to expand it and flare it as well. We have all the dies you need to make your big tubing jobs small ones.


• Long Stroke Bending Cylinder - Because every BendPak bender is equipped with an extended top cylinder, you no longer need to use pusher block extensions when bending with small radius dies. Also, because the 14” top cylinder can be retracted further, additional clearance is provided for changing dies or removing bent tubing.


• BAS Three-Button Control - An automatic control board which is safely enclosed within the front upright of the bender is located up front for operator convenience. The GREEN button is used for full automatic bending functions, the BLUE button for initiating an automatic return sequence and the RED button for automatic stop. The depth-of-bend plate is equipped with an adjustable slide pointer that can be preset to stop at any desired bend depth.


• Clampless Swager - All BendPak benders are equipped with our exclusive Clampless Swager which puts out an incredible force of over 30,000 pounds for quick and precise end forming. The Clampless Swager provides rapid set-up time and a high degree of accuracy for both I.D. and O.D. expansions, slip-fits, flares, ball-joints, reductions, and manifold flanges. All tooling is quick release. Take a close look at the clamp assembly. What you don’t see is a cumbersome, antiquated vise assembly to secure the tubing in the clamp area. What you do see is good old fashioned American ingenuity at it’s finest. The narrow hinged collars simple drop into position and allow you to flare tubing ends as close as 3” from a bend. Don’t worry about the clamps slipping either. The more pressure you put on the clamps the tighter they grip.


• Internal Segment Expander - Our internal segment expander is just as unique as our Clampless Swager and can be used for both I.D. and O.D. expansions, slip-fits, flares, ball-joints, and manifold flanges. Our buttress canister has a single position setting for all I.D. expansions but can also be adjusted for special sizing requirements. A single arbor is used for all tubing sizes 1-1/2” - 3”.


• Electric Foot Switch - An independent remote foot switch allows you to perform manual bending operations standing in front of the bending head or up to 4 feet away. Having the convenience of remote operation is an added plus when handling larger tubing. Switches are industrial grade quality and covered for your protection.

With BendPak’s exclusive “Clampless Swager” and Internal Expander, you can easily perform all of end finishing operations with ease. Reducing, Internal Swaging, Flares, Flat Flares, Ball Joints, Male Ball Joints, Female Sockets, Double Donut-Type Flares, and more. All tooling is quick release.

Our 1302 models are equipped with a double ended cylinder for both the clampless swager and segment expander. A single control handle operates the cylinder and is placed towards the middle so you can stand comfortably in one location and operate both sides.

• Industrial-Grade Hydraulic Cylinders – Integrated into every BendPak bender are commercial-grade hydraulic cylinders that feature one-piece, pilot fitted, machined steel pistons wrapped with specially designed, pressure loaded U-cup piston seals, backups and wear bands that virtually eliminates any fluid bypass. Our micro-smooth chrome-rods are machined from high yield, ground & polished C-1045/50 micro-alloy steel then plated to a minimum of .001˝ diametrically, to ensure superior cylinder operation and life. Specially designed, high durometer, mechanically loaded rod seals virtually eliminate rod seal leakage and a specially formulated abrasion resistant urethane rod wiper provides exclusion protection. Our welded cylinder bodies are made from high yield-strength steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior design ensures straight, smooth and long duty life cylinders.


• Durable Powder Coat Finish – All Pipe Benders feature a durable powder coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected then sandblasted. After, the parts are washed in our five-stage phosphate tanks that can accommodate parts up to 25’ long. Once cleaned, they’re immediately dried, to avoid rust production then outgassed. Outgassing is a process we take pride in which pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely cause chips in the powder. After the parts are washed and outgassed, any surfaces and/or threaded holes that need to be masked or plugged are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints then hung on an electrostatically grounded conveyor line. The powder is then applied using an electrostatic spray gun. The powder “sticks” to the parts similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400 degrees for 15 for 45 minutes.

Our computer exhaust bend data covers over 10,000 applications. The simple computer program system guides you step-by-step when fabricating original equipment exhaust and tailpipes. Coverage includes domestic and light trucks as far back as 1965.

Shipping Details

It is the buyer's responsibility to unload the freight at their location. BendPak will take no responsibility for additional charges of any kind that may incur related to, or involved with, the renting or acquisition of equipment of any kind necessary to unload items off of a delivering carrier's truck. Contact your BendPak dealer for shipping details.

• Two separate end finishing units at rear for all necessary flaring and expanding
• Three-button control for automatic or manual bending operations
• Includes 202 die package (See below)
• Comes complete with quick release bending and end finishing dies
• Includes high-speed clampless swager and internal expander
• Updated bend data system available for automobiles and light trucks dating back to 1960
• Clampless swager - easy to use drop-in collars makes swaging operations quick and efficient
• Twist-lock tooling - quick change tooling saves time
• Integrated power relief control valve - control valve features oversize handles and built in pressure relief system
• Pass-through cylinder stem - the top cylinder stem passes completely through the main frame
• Rigid frame - a rigid 6” x 6” x 3/8” welded steel tube is used for the main frame
• Commercial grade hydraulic cylinders - industrial cylinders provides better performance and reliability
• Chrome-molly shafts - all cylinders features hardened chrome-molly shafts that conform to
  ANSI 92.2 standards
• Quick release bending dies - quick change tooling means faster set up times
• Precision ground bending head - all bending head surfaces are surface ground within .002 of an inch
• Clutter free bending area - controls are enclosed to keep the front obstruction free
• Oversize barrel shafts - large 2-1/2” diameter machined steel barrel shafts used in conjunction with oil impregnated bronze bushings provide ultimate dependability and minimum maintenance
• Grease fittings - standard grease fittings allow for simple lubrication
• Controls - NEMA rated on/off switch box incorporates overload relays that automatically disrupt power supply should an over-current situation occur.
• Pressure gauges - know exactly what the system pressures are at all times
• Industrial grade casters - large cast iron casters help you easily move the bender around your shop
• Remote foot operated controls - our automatic models are equipped with remote foot switches for added operator convenience
• Adjustable pressure valve - adjust back gate pressure easily with this adjustment screw located
  right up front
• One piece barrel - a one piece solid steel barrel is your assurance that the bending gates stay perfectly aligned with the bending ram
• Heat-treated tooling - all machined steel tooling is heat treated for greater service life
• Convenient tool trays - keeps your tooling organized
• Strong motor - a large 5 HP Baldor energy efficient motor is used for maximum performance
• Direct-drive pump - a direct-drive high speed 4 GPM pump is used for maximum
  power and performance
• Single enclosed bottom cylinder - this single bottom cylinder applies pressure evenly to the back gates and because it is hidden, does not interfere with the tubing
• Large capacity reservoir - a large fluid reservoir keeps the hydraulic oil running cooler and contamination to a minimum
• Filtered hydraulic system - a canister type oil filter keeps the oil contamination free
• Oil sight gauges - allows you to visually inspect oil levels
• Over size hose - we purposely use 1/2” high pressure hose for better speed and cooling characteristics
• Open sided swager box - means easier access and less chance of “crashing” tools and
  damaging the cylinder

202 Die Package

BENDING DIES			PIPE COLLARS
QTY.	PART NO.	TOOLING DESCRIPTION	QTY.	PART NO.	TOOLING DESCRIPTION
1	5R-212	5" Radius Die / 2-1/2"	1	HAC-212	2-1/2" Pipe Collar
1	5R-214	5" Radius Die / 2-1/4"	1	HAC-214	2-1/4" Pipe Collar
1	5R-200	5" Radius Die / 2"	1	HAC-200	2" Pipe Collar
1	4R-214	4" Radius Die / 2-1/4"	1	HAC-134	1-3/4" Pipe Collar
1	4R-200	4" Radius Die / 2"	1	HAC-112	1-1/2" Pipe Collar
1	35R-134	3-1/2" Radius Die / 1-3/4"	END FINISHING TOOLS
1	35R-112	3-1/2" Radius Die / 1-1/2"	QTY.	PART NO.	TOOLING DESCRIPTION
BACK SHOES			1	HPF-300	45 / 90-Degree Flare
QTY.	PART NO.	TOOLING DESCRIPTION	1	DD-134/212	Doming Die
2	BS-212	2-1/2" Back Shoes	2	BFED-134/212	Female Ball Flares
2	BS-214	2-1/4" Back Shoes	1	CFT-200	2" Manifold Flange Tool
2	BS-200	2" Back Shoes	1	B-212	2-1/2" Male Ball Flange
2	BS-134	1-3/4" Back Shoes	1	FP-100	Flattening Plate
2	BS-112	1-1/2" Back Shoes	1	ST-1	Slip-Twist Adapter
HALF SHOES			SEGMENT EXPANDERS
QTY.	PART NO.	TOOLING DESCRIPTION	QTY.	PART NO.	TOOLING DESCRIPTION
1	HS-212	2-1/2" Half Shoe	1	HSA-112	Arbor
1	HS-214	2-1/4" Half Shoe	1	SS-212	2-1/2" Segment Exp.
1	HS-200	2" Half Shoe	1	SS-214	2-1/4" Segment Exp.
1	HS-134	1-3/4" Half Shoe	1	SS-200	2" Segment Exp.
1	HS-112	1-1/2" Half Shoe	1	SS-134	1-3/4"- 1-7/8"Segment Exp.
SOLID EXPANDER DIES			1	SS-112	1-1/2" Segment Exp.
QTY.	PART NO.	TOOLING DESCRIPTION	ACCESSORIES
1	STED-212	2-1/2" Exp. Die / 2-1/4" Male Ball	QTY.	PART NO.	TOOLING DESCRIPTION
1	STED-214	2-1/4" Exp. Die / 2" Male Ball	1	TTA-1000	Tool Tray Set
1	STED-200	2" Exp. Die / 1-3/4" Male Ball	2	DPS-150	Pusher Block Springs
1	STED-134	1-3/4" Expander Die	1	Manual	Instruction Manual
1	STED-112	1-1/2" Expander Die	1	Video	Instruction Video
			1	OR-1	Bag / Assorted O-Rings

Specifications

• Maximum bending radius: 5" / 127 mm.
• Minimum bending radius: 3-1/2" / 89 mm.
• Maximum tube capacity: 3" / 76 mm. / .095 wall
• Dies supplied ( 202 Die package ): 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" **
• Top cylinder working force: 60,000 lbs.
• Hydraulic filter: 60,000 lbs.
• Standard motor: 5-HP / 208-230 VAC / 60 HZ. / 1ph.*

* Special voltages available upon request
** Contact factory for metric sizes available
the design, material and specifications are subject to change without notice.

Shipping Information

• Dimensions - 1282 lbs. / 582 kg.
• Shipping Weight - 48" x 70" x 30" / 1219 mm. x 1778 mm. x 762 mm.