Atlas 412AP 4-Post Alignment Lift:
The Atlas 412AP 12,000 pound capacity alignment lift package are designed and built to commercial grade standards and will provide many years of service. Our Atlas alignment packages offer many exclusive features not found on many other competitor’s lifts. Each Atlas 412AP alignment lift package consists of the Atlas 12,000 lb alignment lift, 2 of the
Atlas RJ-6000 rolling jacks (6,000 pound capacity) and a set of front turntables. The turntables can be set in different positions on the runway. There is also an air line kit ($300 value) included with each package. The slip plate package is built into the runways. Drive through ramps are available as an option.
How Do I Get My Stuff Off The Truck?:
Many customers do not have access to loading docks and forklifts.
We have assembled some photos of our products being unloaded with and without the aid of a forklift. Many of our freight carriers have power tailgates on their delivery trucks. There may be an extra charge for the power tailgate, depending on the carrier. The power tailgate is normally rated at 1000 LB. capacity. This is not enough capacity to unload most of our lifts. However, when used properly (and safely), the power tailgate (in conjunction with some common sense) allows the customer to off load many of our products without the use of a forklift.
Most truck shipments will be delivered by a commercial freight carrier operating a tractor/trailer rig. The semi trailer will be enclosed. Most commercial carriers have smaller straight trucks and some have small flatbed trucks, but the majority of freight companies will not use these smaller trucks for your delivery. Atlas Equipment cannot guarantee the type of truck that will be used for delivery. You should assume that your product will be delivered on a tractor/trailer rig that uses a 53 foot enclosed trailer. This is a VERY LONG rig. It is the truck driver's responsibility to make sure that your product is brought to the back of the delivery truck. It is the customer's responsibility to unload the product from the truck.
Features:
The Atlas 412AP (12,000 LB. capacity alignment lift package) incorporates many structural and cosmetic features that are found on lifts costing thousands of dollars more money. The Atlas 412AP is tested to ensure that this alignment lift system will perform flawlessly at its rated capacities. The Atlas 412AP has been manufactured to the same exacting specifications for many years.
The Atlas 412AP uses a high strength cable system (with a under runway oversized hydraulic cylinder) powered by a 220 volt (single phase) power unit to raise and lower the lift. Many competitors use an “old style” chain lifting system with an exposed hydraulic cylinder system. Old style chain lifts are difficult to “level” properly and the exposed hydraulic cylinder is responsible for numerous “door dings”.
The Atlas 412AP alignment system incorporates a lock ladder system in each column and all four column locks are simultaneously air activated from the power unit column. The runways are bolted to the cross tubes, but can be adjusted (moved in) if needed.
One pair (2) of turntables and built-in slip plates are standard with the Atlas 412AP 12,000 LB. four post lift system. The alignment turntables can be moved to two different positions.
Electrical Requirement:
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.
Atlas RJ-6000 Rolling Jacks:
The Atlas RJ-6000 is a heavy duty rolling jack designed to lift and support 6,000 LB. The commercial grade RJ-6000 rolling jack can be used to raise the front or rear portion of a vehicle; allowing the operator of a four post above ground lift to perform wheel and brake service. Most commercial shops buy two of these hydraulic rolling jacks, so that the entire vehicle can be supported in the air at the same time.
The Atlas RJ-6000 has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS that are located over the runways of the four post lift. The Atlas RJ-6000 rolling bridge is equipped with expandable supports which adjust to fit many different brands of four post above ground lifts. These supports have a unique roller system that allows the rolling hydraulic jack to glide easily under the entire length of the vehicle. The large heavy steel wheels allow the rolling jack to be positioned under the correct lifting points in a matter of seconds.
The Atlas Atlas RJ-6000 comes standard with a set of peg style truck adapters which increases the lifting height of the lift pads. These truck adapters will allow the Atlas RJ-6000 rolling hydraulic jack to raise most pick up and larger trucks that will sit higher than the average passenger car.
The Atlas RJ-6000 can be equipped with an optional
Atlas Deluxe Air/Hydraulic Pump. The air/hydraulic pump would require a supply of compressed air (air compressor) to work properly.
The Atlas RJ-6000 rolling hydraulic jack features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas RJ-6000 are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).
"World-Class" Products:
Atlas Equipment is proud to state that our manufacturers are definitely “world-class”. Our Atlas products are sold throughout the world.
Instruction manuals that accompany products may contain certain specifications that do not apply to the product when used in the USA or Canada.
